Reinventing
the wheel (5)

Original page created on 18/08/2022.

Router template

In the series of woodworking DIY, and keeping in mind the principles of material recycling and maximum simplicity, here is an adjustable router template, strongly inspired by this John Heisz video.

A little searching on the web will reveal other videos that present the same principle, but in a much more elaborate form, or using more sophisticated tools. Here are some examples by Thosa or Mr.H Woodworking in English.

What I am proposing requires at least a drill, preferably on a stand, a circular saw and, of course, a router, but the latter just for future use, not for manufacturing…

This template is used to guide the router to make a rectangular depression of a size ranging from the width of the router to a maximum that will only depend on the length of the parts.

Template drawing and description

Warning: this drawing has been redone after the assembly that I present below, taking into account the possible improvements that I didn’t think of at the time.

Template seen in perspective

The inner rectangle in dashed line shows the path
of a ⌀ 10 mm milling bit.

The template is made of four identical parts, except possibly for the length. Only two of them are represented in 3D, with false colours, one in light brown, the other in green. Each part consists of two strips of plywood (PLY), 10 mm thick, between which spacers of the same material provide a groove. In this groove slides a screw belonging to the neighbouring part, perpendicular to it. Once the position has been reached, a wing nut locks the part.

The trapezoidal pieces serve to increase the seating capacity of the assembly. They are not necessary. Wider strips, e.g. 50 mm, can also be considered, which would dispense with these pieces, with the disadvantage of making the whole thing heavier.

The dimensional drawing of the parts is available here as a PDF.

It goes without saying that the dimensions can be modified depending on the materials available and also the type of router you have.

List of parts

Designation Dimensions Quantity
PLY 10 mm thick 550 or more × 30 8
     ” 30 × 30 4
     ” 130 × 60 4, drilled ⌀ 7,5, depth 50
Threaded rod ⌀ M8 × 80 4
Wing nut M8 4
Steel support 73 × 25 × 2 4, drilled ⌀ 8

Personally, I had to buy the threaded rod only.

Implementation and modifications

I start by cutting the various PLY strips, all 30 mm wide.

The 60 mm wide pieces mentioned in the list (trapezoids) are not part of the prototype. Instead, I used battens set to the height of 30 mm, which is the three PLY layer stack height.

The spacers are of two types: length 30 and length 50, the latter being drilled to ⌀ 7.5 and then “tapped” by force-fitting an M8 threaded rod (or screw). In the photo, the drilled spacers are also 30 mm long, but it will be seen later that some of them have been replaced by 50 mm pieces, which fit into the groove and hold the whole thing flat.

Overview of the parts

Notes:

Grinding

It’s necessary to ensure that the parts are perpendicular. If you have an accurate table saw, you may not need the following, but I do. So, I ground the ends of the parts by milling.

The parts are screwed and glued together and placed in the vice of the milling machine. Milling in two passes, changing the depth to cover the 30 mm thickness. For parts with a protruding spacer, these are not glued at first, only screwed. For grinding, they are dismantled and replaced by temporary spacers. They are then reassembled and glued in place.

Grinding the ends

This picture is only a reconstruction afterwards, and the batten that should be fixed on the side is missing. The top pass has been done, the current pass is 15 mm lower.

Finally, the threaded rods are glued with CA and screwed in place. They protrude 50 mm from the support face.

View of the assembled parts

This picture shows the 50 mm spacers which are used for guiding in the groove. The other two were already glued when I thought of this improvement and remained as they were.

Close-up of the mounted parts

You can see a temporary spacer in the groove of the part in the background. Seeing this, I thought that the spacers could be as long as the battens, and could even replace them, hence the new diagram.

Assembly

The pieces fit together almost naturally. I tried three settings, one large:

Large template

The orthogonality verified by the equality of the diagonals is very good.

A medium one:

Rectangular template

And a small one:

Small template

In the latter case, the router will only have a very small travel!

Setting the scene:

Setting the scene with the router

Remarks:

For storage, once the parts have been dismantled, the space required is reduced:

Part storage

Conclusion

I still have to find an excuse to use this template! As often, it’s after I needed it that the idea came to me, greatly helped by the video quoted at the beginning of this text.

Threaded rod M8 × 1000 mm
Reference 35736862
€1,90 (price 2022) at Leroy-Merlin.

6 M8 wing nuts
Reference 82583022
€3,90 (price 2022) at Leroy-Merlin.

These parts are nothing else than Hornby-Jouef
wagon weights!
They can be replaced by wide washers, but the
bearing surface will of course be reduced.